一个路由器就是一块开发板--淘宝50元淘来的无线路由
型号 LINKSYS WRT54GP2A-AT 54M无线路由+2口VOIP网络电话
CPU Intel IXP425RAM 32MFLASH 8M
内部的WIFI网卡插在PCI接口 INPROCOMM IPN2220 54M无线内置网卡
收到货马上配置好，竟然没问题， （用了几天也没发现问题，就是信号差点）
验明正身后当然就要开始剥衣服了{:lol:}，剥完衣服观摩一番后就开始找可以进入的地方了
JTAG很容易就看出来了，因为是20脚，有一边很多地线的
串口（系统控制台）稍微试了一下也找到了TX RX 脚，通信参数搞多了的都猜得到是115200 8N1 无流控
Pin(s) Desig. Dest Desig.
1,2 Vcc
3 tts/1 TXD
4 tts/0 TXD
5 tts/1 RXD
6 tts/0 RXD
7,8 NC
9,10 GND GND
连上超级终端
Starting EthAcc component ...
0x1fffe68 (tRootTask): ixQMgrInit: IxQMgr initialise
ixe ETH PHY 0 Hard Coded MAC address is: 00:12:17:cc:72:2b
ixe ETH PHY 1 Hard Coded MAC address is: 00:12:17:cc:72:2c
VxWorks System Boot
Copyright 1984-2002Wind River Systems, Inc.
CPU: WRT54GP2A-AT
Version: VxWorks5.5.1
BSP version: 1.3/3
Boot version: 0.00.f
Creation date: Sep 29 2004, 14:17:09
Press any key to stop auto-boot...
0
auto-booting...
boot device : tffs:
unit number : 0
processor number : 0
file name : /fl/vxWorksB.sys
inet on ethernet (e) : 192.168.1.1:ffffff00
host inet (h) : 192.168.1.100
user (u) : target
flags (f) : 0x0
target name (tn) : targetname
other (o) : ixe
Attaching to TFFS... done.
Loading /fl/vxWorksB.sys... 3302292
Starting at 0xa80000...
PCI Device Table
---------------------------------------
Bus Slot Func Vendor Device BAR
=== ==== ==== ====== ================
00 00 00 0x17fe 0x22200x100000
---------------------------------------
Host Name: bootHost
Starting EthAcc component ...
0x1fffe68 (tRootTask): ixQMgrInit: IxQMgr initialise
ixe ETH PHY 0 Hard Coded MAC address is: 00:12:17:cc:72:2b
ixe ETH PHY 1 Hard Coded MAC address is: 00:12:17:cc:72:2c
Return ixp425 wlan name string..
Parsed unit number 0
Start call i2220ap_priv_create
End call i2220ap_priv_create
Mem setup complete
Done load Wlan
Attached TCP/IP interface to ixe unit 0
Attaching network interface lo0... done.
Multicast MAC: 01:00:5e:00:00:01 ( ff:ff:ff:ff:ff:ff )
Constituent Addresses:
01:00:5e:00:00:01
Adding 21903 symbols for standalone.
]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]]]]]] ]]]]]]]]]] ]] ]]]] (R)
] ]]]]]]]]]]]]]]] ]]]]]]]] ]] ]]]]
]] ]]]]]]]]]]]]]]] ]]]]]] ] ]] ]]]]
]]] ]]]]] ] ]]]] ]]]] ]]] ]]]]]]]]]]]]] ]] ]]]]]] ]]]]]
]]]] ]]]]] ]]]] ]] ]]]]] ]]]]]] ]] ]]]]]]] ]]]] ]] ]]]]
]]]]] ]]]]] ]]]]] ]]]]]]]] ]]]] ]] ]]]] ]]]]]]] ]]]]
]]]]]] ]]]]] ]]]]]] ]]]]]]]]]] ]] ]]]] ]]]]]]]] ]]]]
]]]]]]] ]]]]]] ]]]]]]] ]]] ]]]] ]] ]]]] ]]]] ]]]] ]]]]
]]]]]]]]]]]]]]]] ]]]]]]] ] ]]]]]]]]]]] ]]]]]]]] ]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]]]] Development System
]]]]]]]]]]]]]]]]]]]]]]]]]]]]
]]]]]]]]]]]]]]]]]]]]]]]]]]] VxWorks version 5.5.1
]]]]]]]]]]]]]]]]]]]]]]]]]] KERNEL: WIND version 2.6
]]]]]]]]]]]]]]]]]]]]]]]]] Copyright Wind River Systems, Inc., 1984-2003
CPU: .Processor #0.
Memory Size: 0x2000000.BSP version 1.3/3.
check file system now !
dosChkLib : CLOCK_REALTIME is being reset to FRI APR 13 06:13:00 2012
Value obtained from file system volume descriptor pointer: 0x17dfef0
The old setting was THU JAN 01 00:00:00 1970
Accepted system dates are greater than THU DEC 27 00:00:00 1990
/fl/- Volume is OK
ixdp425EthEndStartUp: Forcing Hard Coded IP Address for ixe1
Multicast MAC: 01:00:5e:00:00:01 ( ff:ff:ff:ff:ff:ff )
Constituent Addresses:
01:00:5e:00:00:01
ixdp425EthEndStartUp: ixe1: IP Addr set to 192.168.60.1
bridgePortAdd ******** for ixe0*****************
Return ixp425 wlan name string..
bridgePortAdd ******** for Frisbee0*****************
_____________ get mac = 0x72 mac = 0x2b
_____________ get mac = 0x72 mac = 0x2b
-> prio = 150,snmpdTaskOptions=0,stackSize=28672,traceLevel Log Length=0
Start Initial MEM Drv
Copy OK: 57470 bytes copied
CC module initialized successfully
FlshFormatFileSystem: Invalid Filesys ID -1
vxBitsInit
Return ixp425 wlan name string..
aIfName = mirror0
Return ixp425 wlan name string..
!!!!!!!!!!!!!!Find Interface mirror0
aIfName = ixe1
!!!!!!!!!!!!!!Find Interface ixe1
Return ixp425 wlan name string..
aIfName = Frisbee0
Error 0xffffffff Couldn't add Input Hooks
WAN Initialisation
PPPoE Initialised
PPTP Initialised
L2TP Initialization success
Firewall INIT completed
AD Init completed FW initalized
** before calling dhcpc http register function **
TFTPD:Initializatinion ok ...............
IGWIpRsmInit():....End
Initialising UPnP Stack DEBUG: IGWHttpServStart: server is now running
UPnP Stack InitialisedRegistered MsgClnt
load<==>ulTotalLen = 1708, ulFlashchecksum=133958, ulCheckSum = 20b46
IGWUPNLdSvInit 54
IGWIGDLoadAndSaveInit: success
../../ldsvcbk/firewall/kukildsv.c(76): FWCookieLdsvInit: SUCCESS
***********************************************************
* LDSV Flash VERSION *
* matching code LDSV VERSION , OK *
***********************************************************
IpAddRoute : iproute->ifname ixe1
Loading RIP configuration records - success.
Loaded RIP database
Return ixp425 wlan name string..
Return ixp425 wlan name string..
standard_tftp_server launched on port 69.
DNSRDLoad Done
DNSRDLoadSysDName Done
Firewall load database completed Loaded Security database
Dns ALG loaded
IGWIGD: Loading data
lTotalRecs is 2
IGWUPnPIGDGetWanConnStatus: WanGetExactStatsByUser : DIM : No Such DiUser
IGWIGDSetIface/Ethernet/PPP Conn Service: No PPP Interface found with name ----
IGWIGDLoadEnable :lTotalRecs is 1
UPnPPeriodicAdvertiseRestatr: Starting Advt.
IGWIGDLoad:IGWIGDLoad() success
IGWUPN: Loading data
IGWUPNLoadData 74
IGWUPNLoadHostRec 266
IGWUPNLoadServRec 352
IGWUPNLoadServRec: DbGetRecordInfo Failed IGMPPoly DefaultDMZ is 21
test 2 - fffffff7 = b
Sucess Init Wireless.
Httpd_Register_TagArray
Wake up packet recvived
index = 1
DLcid 02050100-01
********************************************
* Intel IXP400 DSP Software *
* Release 2.5 EAR *
* Jan 23 2004, 16:27:18 *
* Intel Corporation *
********************************************
Initializing Slic's, please wait...
UPnPPeriodicAdvertiseRestatr: Starting Advt.
*** DnsResolveAPI PeerIp:2030708891 host:sasvp.callvantage.att.com***
当然也可以像U-BOOT那样在系统启动时按任意键进入BOOTLOADER
: ?
? - print this list
@ - boot (load and go)
p - print boot params
c - change boot params
l - load boot file
g adrs - go to adrs
d adrs[,n] - display memory
m adrs - modify memory
f adrs, nbytes, value - fill memory
t adrs, adrs, nbytes- copy memory
e - print fatal exception
v - print boot logo with version
n netif - print network interface device address
$dev(0,procnum)host:/file h=# e=# b=# g=# u=usr f=#
tn=targetname s=script o=other
boot device: tffs=drive,removable file name: /tffs0/vxWorks
Boot flags:
0x02- load local system symbols
0x04- don't autoboot
0x08- quick autoboot (no countdown)
0x20- disable login security
0x40- use bootp to get boot parameters
0x80- use tftp to get boot image
0x100 - use proxy arp
available boot devices:Enhanced Network Devices
ixe0 ixe1 tffs
:
有点失望是VXWORK而不是LINUX系统，也就没第三方固件可以刷了，但好消息是DD-WRT（第三方路由器固件，可以下载源码）正在移植LINUX到这个设备上，网上貌似也有人移植LINUX成功了
其实WRT54GP2A-AT 可以安装redboot 后再装XScale架构版本的openwrt，但是VOIP就失效了，不过性能和功能要增强很多
这二天预备潜心研究一下wrt54gp2a-at，让它跑openwrt。 今天的成果，基本完成redboot的。
+
RedBoot(tm) bootstrap and debug environment
Red Hat certified release, version 2.02 - built 00:07:02, May9 2010
Platform: Linksys WRT54GP2A-AT (IXP42X 400MHz) BE
Copyright (C) 2000, 2007, 2008, 2009, 2010 Red Hat, Inc.
RAM: 0x00000000-0x02000000, available
FLASH: 0x50000000 - 0x50800000, 64 blocks of 0x00020000 bytes each.
== Executing boot script in 2.000 seconds - enter ^C to abort
今天完成openwrt。
+
RedBoot(tm) bootstrap and debug environment
Red Hat certified release, version 2.02 - built 00:07:02, May9 2010
Platform: Linksys WRT54GP2A-AT (IXP42X 400MHz) BE
Copyright (C) 2000, 2007, 2008, 2009, 2010 Red Hat, Inc.
RAM: 0x00000000-0x02000000, available
FLASH: 0x50000000 - 0x50800000, 64 blocks of 0x00020000 bytes each.
== Executing boot script in 2.000 seconds - enter ^C to abort
RedBoot> fis load linux
RedBoot> exec
Using base address 0x00024c00 and length 0x000c865c
Uncompressing Linux... done, booting the kernel.
Linux version 2.6.32.10 (openwrt@localhost.localdomain) (gcc version 4.3.3 (GCC) ) #1 Sun May 9 15:13:09 CST 2010
CPU: XScale-IXP42x Family revision 1 (ARMv5TE), cr=000039ff
CPU: VIVT data cache, VIVT instruction cache
Machine: Linksys WRT54GP2A-AT
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on.Total pages: 8128
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 32MB = 32MB total
Memory: 30164KB available (2064K code, 130K data, 88K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:32
Calibrating delay loop... 398.95 BogoMIPS (lpj=1994752)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
IXP4xx: Using 16MiB expansion bus window size
PCI: IXP4xx is host
PCI: IXP4xx Using direct access for memory space
PCI: bus0: Fast back to back transfers disabled
pci 0000:00:01.0: dmabounce: registered device
bio: create slab <bio-0> at 0
Switching to clocksource OSTS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
IXP4xx Queue Manager initialized.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)漏 2001-2006 Red Hat, Inc.
msgmni has been set to 58
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xc8001000 (irq = 13) is a XScale
console enabled
IXP4XX-Flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
Searching for RedBoot partition table in IXP4XX-Flash.0 at offset 0x7e0000
5 RedBoot partitions found on MTD device IXP4XX-Flash.0
Creating 5 MTD partitions on "IXP4XX-Flash.0":
0x000000000000-0x000000060000 : "RedBoot"
0x000000060000-0x000000140000 : "linux"
0x000000140000-0x0000007e0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=400000, len=3E0000
0x000000400000-0x0000007e0000 : "rootfs_data"
0x0000007e0000-0x0000007ff000 : "FIS directory"
0x0000007ff000-0x000000800000 : "RedBoot config"
IXP4xx MII Bus: probed
eth0: MII PHY 32 on NPE-B
eth1: MII PHY 1 on NPE-C
i2c /dev entries driver
IXP4xx Watchdog Timer: heartbeat 60 sec
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
XScale DSP coprocessor detected.
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing init memory: 88K
Please be patient, while OpenWrt loads ...
- preinit -
Press the key and hit to enter failsafe mode
- regular preinit -
switching to jffs2
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
- init -
Please press Enter to activate this console. net eth0: firmware: requesting NPE-B
NPE-B: firmware's license can be found in /usr/share/doc/LICENSE.IPL
NPE-B: firmware functionality 0x2, revision 0x2:1
eth0: link up, speed 0 Mb/s, full duplex
device eth0 entered promiscuous mode
br-lan: port 1(eth0) entering forwarding state
net eth1: firmware: requesting NPE-C
NPE-C: firmware's license can be found in /usr/share/doc/LICENSE.IPL
NPE-C: firmware functionality 0x5, revision 0x2:1
Generic kernel compatibility enabled based on linux-next next-20100113
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
PCI: enabling device 0000:00:01.0 (0140 -> 0142)
Registered led device: rt2500pci-phy0::radio
Registered led device: rt2500pci-phy0::quality
PPP generic driver version 2.4.2
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (472 buckets, 1888 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
IMQ driver loaded successfully.
Hooking IMQ before NAT on PREROUTING.
Hooking IMQ after NAT on POSTROUTING.
xt_time: kernel timezone is -0000
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
device wlan0 left promiscuous mode
br-lan: port 2(wlan0) entering disabled state
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
BusyBox v1.15.3 (2010-05-09 14:54:15 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.||||.----.||_
| - ||_|-__| |||||| _|| _|
|_______|| __|_____|__|__||________||__||____|
|__| W I R E L E S S F R E E D O M
Backfire (10.03, r21402) --------------------------
* 1/3 shot Kahlua In a shot glass, layer Kahlua
* 1/3 shot Bailey'son the bottom, then Bailey's,
* 1/3 shot Vodka then Vodka.
root@OpenWrt:/# ifconfig
br-lan Link encap:EthernetHWaddr 00:03:47F:32:A8
inet addr:192.168.1.1Bcast:192.168.1.255Mask:255.255.255.0
UP BROADCAST RUNNING MULTICASTMTU:1500Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:1 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B)TX bytes:402 (402.0 B)
eth0 Link encap:EthernetHWaddr 00:03:47F:32:A8
UP BROADCAST RUNNING MULTICASTMTU:1500Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:1 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 B)TX bytes:402 (402.0 B)
eth1 Link encap:EthernetHWaddr 00:03:47F:32:AA
UP BROADCAST MULTICASTMTU:1500Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 B)TX bytes:0 (0.0 B)
lo Link encapocal Loopback
inet addr:127.0.0.1Mask:255.0.0.0
UP LOOPBACK RUNNINGMTU:16436Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B)TX bytes:0 (0.0 B)
mon.wlan0 Link encap:UNSPECHWaddr 00-18-01-E3-D5-99-00-00-00-00-00-00-00-00-00-00
UP BROADCAST RUNNING MULTICASTMTU:1500Metric:1
RX packets:2 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:254 (254.0 B)TX bytes:0 (0.0 B)
wlan0 Link encap:EthernetHWaddr 00:18:01:E35:99
UP BROADCAST MULTICASTMTU:1500Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:1 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B)TX bytes:420 (420.0 B)
root@OpenWrt:/# df
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 2816 2816 0 100% /rom
tmpfs 15128 40 15088 0% /tmp
tmpfs 512 0 512 0% /dev
/dev/mtdblock3 3968 408 356010% /overlay
mini_fo:/overlay 2816 2816 0 100% /
root@OpenWrt:/# free
total used free shared buffers
Mem: 30252 13140 17112 0 1672
Swap: 0 0 0
Total: 30252 13140 17112
root@OpenWrt:/# cat /proc/cpuinfo
Processor : XScale-IXP42x Family rev 1 (v5b)
BogoMIPS : 398.95
Features : swp half fastmult edsp
CPU implementer : 0x69
CPU architecture: 5TE
CPU variant : 0x0
CPU part : 0x41d
CPU revision : 1
Hardware : Linksys WRT54GP2A-AT
Revision : 0000
Serial : 0000000000000000
root@OpenWrt:/# lspci
00:01.0 Network controller: RaLink RT2500 802.11g Cardbus/mini-PCI (rev 01)
root@OpenWrt:/#
inksys wrt54gp2a-at voip 语音网关设置配置破解方法完全讲解。网上有好多讲linksys wrt54gp2a-at这个无线路由器破解语音网关的，但都不完整，现配合米酷（meecall）细说一下：
1.需要下载两个文件，因服务器不能上传大于200k文件的原因，故未上传，需要的话可以向我索要。
2.先打开第一个文件sipothers.htm，保存。再打开sip.htm文件后更改平台地址和端口,设置好两个线路用户名密码.直接保存。这里说一下meecall的设置。
前面两个地址与端口都填219.233.239.100 5060
id与认证用户名都是你的帐号，密码上下都填一样。
3.打开sipothers文件已完全设置好，直接保存一下就行。
4.如果没有特别的需求请使用国内手机和通用座机的规则：010xxxxxxxx|0xxxxxxxxx|013xxxxxxxxx
支持国内13/15/18号段手机号码，支持国内长途，区号加电话号码不足11位的，加拨#，号码拨完后加拨#会立刻发送至服务器；
你也可以使用以下规则：
1xxxxxxxxx|01xxxxxxxxx|0xxxxxxxxxx|100x|xxx|20xxxxxx|*xxxxxxxxxxxx|00x.t
现在可以直接打移动、联通手机，还可以直接打2位区号+8位座机号或3位区号+7位座机号以及4位区号+6位座机号的座机电话了，其它区号加座机号少于10位的拨完后要加#号键。
拨号规则,只建了一个xxxxxxxxxxxx,所有都能打通,位数不够可以在后面打#,打#后是立即拨出的意思.大家可以试试,
5.打开第一个文件sipothers.htm要口令是因为绑定了供应商，你可以在打开的时候点浏览器倒退按钮然后立刻按ecs键，我这样成功了，你也可以直接关闭不理它。或者你关闭浏览器的java功能。
6.如果想调测qos,直接拷贝地址,然后自己看能否设置!
附带dial plan的语法规则
如( *xx | 11 | 0 | 00 | <:1408>xxxxxx | 1xxxxxxxx | 011x. )
１．其中每条规则之间使用“ | ”隔开，整个dial plan 需用双括号括住。
２．如需将所拨号码立即拨出，可以在号码后加拨“＃”。
３．x 代表０－９之间任意一个键。
４．［］代表可取括号中任意一个数，如［７８９］代表可取７，８，９中任意一个键，［２３５－７*］代表可在２，３，５，６，７，*中取任意一个键。
５．<:>可用于拨号头的替换，如<8:1650>xxxxxxx 当你拨打“８５５５１２１２”，而实际发送出去的号码是 “１６５０５５５５１２１２”
６．9, 1xxxxxxxxxx，逗号代表发送拨号音，等待继续拨号。
７．190xxxxxxx!，规则后带有叹号，表示符合该规则的拨号被禁用，无法拨出。
８．设置拨号超时时间，可在双括号前加入“ｌ＝８，ｓ＝４”，代表超时间为８秒。
９．011x.，x后面的点号代表与前一项定义相同，不限制长度，所以01122,011223,0112234都符合规则
范例：
( 1 xxx xxxxxxx ) 表示拨打美国号码，前面的xxx代表区码
( 1 xxx xxxxxxx | <:1212> xxxxxxx )表示如果只拨入７个号，则自动加入前码１２１２用于拨本地号码
( <9,:> 1 xxx xxxxxxx | <8,:1212> xxxxxxx ) ９和８用于小总机拨外线的预拨号码，当拨９或８时，可听到等待音
s:4, ( 00 | 011 xxxxx x. ) 设置的短超时为４秒，只可拨打００或以０１１开头的号码
( 0 | 11 | 1 xx xxxxxx ) 用于直拨４１１或９１１
( 1 xx xxxxxx ) 典型的美国电话规则
( 1 947 xxxxxxx ! | 1 xxx xxxxxxx ) 禁拨区号为９４７的电话
( s0 <:12125551234> ) 热线拨出，拿起电话，自动拨出号码12125551234
( p5 <:1000> | xxxx ) 如果用户没有拨入四个号码，则５秒后自动拨出１０００
想用JTAG把FLASH里的原版固件读出来，这样就没后顾之忧就可以为所欲为了，可惜用H-JTAG只认到了芯片，没能读写FLASH（应该是FLASH初始化指令部分不会写）
网上说 jlink不行OPENOCDv728 FT2232线可写 读的话用wiggler和USB的H-JTAG都行
网上找到了一个JTAG读出来的固件（8M） 貌似上传不了，有需要的就联系我吧 破解网络电话VOIP要用到的两个文件
楼主牛X。我也有个wrt54g v4 刷了dd-wrt。这路由器信号还不错 这个路由器的使用说明书
DD-WRT是啥东东，路由器怎么还有第三方开源固件
Cisco /Linksys公司在2003年发行的WRT54G/GS无线路由器使用802.11g标准，使得带宽在理论上能够达到54M。有Linux爱好者在Linux Kernel Mailing List搜索WRT54G，发现它的IOS是基于Linux，然而Linux 基于GPL(GNU General Public License) 发布许可证，该许可证规定Cisco应该把WRT54G/GS的IOS的源代码公开。2003年三月，基于公众压力Linksys公开了WRT54G的源代码。此后就有了一些基于linksys源代码的第三方固件，当Linksys释放WRT54G/GS的源码后，网上出现了很多不同版本的固件去增强原有的功能。大多数的固件都是99%使用Linksys的源码，只有1%是加上去的，每一种固件都是针对特定的市场而设计，这样做有两个缺点，第一个是难以集合各版本固件的长处，第二个是这版本距离Linux正式发行版越来越远。OpenWRT选择了另一条路，它从零开始，一点一点的把各软件加入去，使其接近Linksys版固件的功能，而OpenWRT 的成功之处是它的文件系统是可写的，开发者无需在每一次修改后重新编译，另它更像一个小型的Linux电脑系统，也加快了开发速度。最后到后来就出现了openwrt，ddwrt，tamato，还有个用得少的waysos 内容很不错。我也心动想买一块板了 楼主威武，带着我们一起玩哦。。 楼主带着我们一起玩啦。 很早之前就有玩DD了，但沒怎麼玩，最近買了幾個F5D7230,想玩，最後發現被坑爹了，版本是4000的無法玩，正準備測量線路，看看有哪位高人能一起玩，跟著學學。 学习学习了,以后也淘个了折腾 又是一个路由当开发板的，把平板拿来当开发板一定也有意思，现在电容屏的A8平板也就400了{:lol:} 瓦擦~学习了！ 不懂linux，openwrt玩不深 tsb0574 发表于 2012-4-28 14:40 static/image/common/back.gif
不懂linux，openwrt玩不深
你都玩神马的？ 买来diy. 这个感觉好强大啊，看不懂啊，呵呵 mark................... 这个路由器我也有一个，一直在服役中，打网络电话还不错，用了5年多了。 我也有这样一个老路由器，下试试次也能 下次也到网上买个这样的路由器试试。 楼主，能否公开一下openwrt部分的修改代码呢？我刷了你的redboot，然后编译了最新的WRT300N V2的OP固件刷上去，只能找到LAN，找不到WAN。而且我也换了RT25xx的网卡。驱动也编译进去了。但是找不到网卡。
先谢谢了。 很复杂的样子，mark下，等学好了基础常识，回头再深究。 学习了，比较高深 留个记号 学习一下.... 留个记号 我现在手里在研究这个路由器 hame A5（号称世界上最小的3G路由器）带1个WAN/LAN自适应网卡，一个USB 2.0 Host接口，无线支持802.11b/g/n 150M
http://img30.360buyimg.com/erpWareDetail/g9/M03/00/15/rBEHaVA3YPUIAAAAAAE6-l8begYAAAIhgJUC4YAATsS254.jpg 目前已经引出TTL串口，刷openwrt成功，无线AP功能已经开启，USB口可以挂载U盘 {:lol:}
页:
[1]