发个LCD12232液晶驱动程序

meisen999 · 发表于 2007-9-29 20:53:10

显示效果如下:

程序:
#include <AT89X51.h>
#include <absacc.h>
/*----接口说明--------*/
/*rst--P1^0;  e1 =P1^1; e2 =P1^2 ;rw =P1^3;a0 =P1^4;*/
/*-----送数据口:P0--------*/

#define dat  1       //写数据标志
#define comm  0    //写指令标志
#define f_page  0xb8  //页地址设置(0~3)
#define f_row 0xc0  //显示起始地址
#define f_line  0x00  //列地址设置(0~61)

sbit rst=P1^0;
sbit e1 =P1^1;
sbit e2 =P1^2;
sbit rw =P1^3;
sbit a0 =P1^4;

sbit bf =P0^7; //lcd忙检测位

void wr_lcd (unsigned char choe1,unsigned char choe2,unsigned char data_comm,unsigned char content);
/*choe1为1,控制左半屏,choe2为1,控制右半屏*/
void chk_busy (unsigned char choe1,unsigned char choe2); /*忙检测*/
void delay (unsigned int us);
void delay1 (unsigned int ms);
void init_lcd (void);          /*液晶初始化*/
void disphz (unsigned char code *chn);
void dispzf (unsigned char code *chn);
void disptu (unsigned char code *img);
void wrlattice (unsigned char data1,unsigned char data2); /*写点阵*/
void Write_One_Chinese(unsigned char x,unsigned char y,unsigned char code *chinese);
/*一串到指定位置写汉字*/
void Write_Chinese_Characters(unsigned char row,unsigned char line,
unsigned char code *characters,unsigned char chinese_num);

/******************************************************字模**************************************/
//字模:"三木多功能实验板"
unsigned char code sanmu[]={
0x00,0x00,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x88,0x0C,0x00,0x00,0x00,0x20,
0x20,0x21,0x21,0x21,0x21,0x21,0x21,0x21,0x21,0x20,0x20,0x00,0x00,0x00,/*"三",0*/
0x00,0x00,0x20,0x20,0x20,0xE0,0xFE,0x62,0xA0,0x20,0x20,0x10,0x00,0x00,0x00,0x10,
0x08,0x04,0x02,0x01,0xFF,0x00,0x01,0x02,0x0C,0x18,0x00,0x00,0x00,0x00,/*"木",1*/
0x00,0x00,0x20,0x20,0x10,0x98,0xA4,0xC8,0x48,0x28,0x18,0x08,0x00,0x00,0x00,0x80,
0x82,0x89,0x85,0x44,0x5B,0x21,0x12,0x12,0x0E,0x06,0x02,0x00,0x00,0x00,/*"多",2*/
0x00,0x00,0x10,0xF0,0x10,0x10,0x28,0x20,0xF8,0x26,0x20,0x20,0xE0,0x00,0x00,0x10,
0x08,0x0F,0x88,0x44,0x20,0x18,0x07,0x40,0x40,0x7E,0x01,0x00,0x00,0x00,/*"功",3*/
0x00,0x70,0xA8,0xA4,0xA0,0xE8,0x30,0x00,0x7C,0x90,0x88,0x88,0x60,0x00,0x00,0x00,
0x7F,0x0A,0x4A,0x7F,0x00,0x00,0x7E,0x48,0x44,0x42,0x70,0x00,0x00,0x00,/*"能",4*/
0x00,0x20,0x38,0x10,0x30,0xD0,0x0A,0xD4,0x30,0x10,0x10,0x10,0x18,0x00,0x00,0x84,
0x84,0x85,0x47,0x24,0x14,0x0F,0x14,0x24,0x24,0x44,0x04,0x00,0x00,0x00,/*"实",5*/
0x00,0xC0,0x38,0x08,0xFC,0x80,0x40,0xB0,0x8E,0x88,0xB0,0x40,0x40,0x00,0x00,0x09,
0x0A,0x41,0x7E,0x43,0x46,0x58,0x46,0x68,0x58,0x46,0x40,0x00,0x00,0x00,/*"验",6*/
0x00,0x00,0xE0,0xFE,0x90,0x20,0xF8,0xC8,0x48,0x44,0xC4,0x62,0x00,0x00,0x00,0x06,
0x01,0x7F,0x41,0xB8,0x47,0x21,0x16,0x0C,0x33,0x60,0x40,0x00,0x00,0x00,/*"板",7*/
};

//字模"小灵通号"
unsigned char code moble[]={
0x00,0x00,0x00,0x80,0x60,0x00,0x00,0xFE,0x00,0x40,0x80,0x00,0x00,0x00,0x00,0x04,
0x02,0x01,0x00,0x40,0x40,0x3F,0x00,0x00,0x00,0x03,0x06,0x00,0x00,0x00,/*"小",0*/
0x00,0x00,0x40,0x54,0x54,0x54,0xD4,0x54,0x54,0x54,0x7E,0x00,0x00,0x00,0x00,0x80,
0x44,0x43,0x30,0x0C,0x03,0x0C,0x14,0x22,0x21,0x40,0x40,0x00,0x00,0x00,/*"灵",1*/
0x00,0x00,0x84,0x48,0x00,0xF0,0xA4,0xAC,0xFC,0xAC,0xA4,0xF4,0x00,0x00,0x00,0x20,
0x1F,0x10,0x20,0x5F,0x42,0x42,0x5F,0x52,0x52,0x5F,0x00,0x00,0x00,0x00,/*"通",2*/
0x00,0x80,0x80,0xFE,0xA4,0xA4,0xA4,0xA4,0xA4,0xA4,0xBC,0x80,0x80,0x00,0x00,0x00,
0x00,0x00,0x06,0x05,0x04,0x44,0x44,0x64,0x1E,0x00,0x00,0x00,0x00,0x00,/*"号",3*/
};

unsigned char code moble_num[]={
0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00,/*"0",0*/
0x00,0x38,0x08,0x08,0xE8,0x18,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,/*"7",1*/
0x00,0x38,0x08,0x08,0xE8,0x18,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,/*"7",2*/
0x00,0x30,0x08,0x88,0x88,0x70,0x00,0x00,0x18,0x20,0x20,0x31,0x1E,0x00,/*"3",3*/
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x00,/*"-",4*/
0x00,0x70,0x08,0x08,0x08,0xF0,0x00,0x00,0x30,0x2C,0x22,0x21,0x30,0x00,/*"2",5*/
0xF0,0x08,0x08,0x08,0x18,0xE0,0x00,0x31,0x22,0x22,0x32,0x19,0x07,0x00,/*"9",6*/
0xF0,0x08,0x08,0x08,0x18,0xE0,0x00,0x31,0x22,0x22,0x32,0x19,0x07,0x00,/*"9",7*/
0xE0,0x10,0x88,0x88,0x88,0x18,0x00,0x0F,0x11,0x20,0x20,0x31,0x1F,0x00,/*"6",8*/
0x70,0x98,0x88,0x08,0x98,0x70,0x00,0x1E,0x21,0x21,0x21,0x31,0x1E,0x00,/*"8",9*/
0x70,0x98,0x88,0x08,0x98,0x70,0x00,0x1E,0x21,0x21,0x21,0x31,0x1E,0x00,/*"8",10*/
0x00,0x30,0x08,0x88,0x88,0x70,0x00,0x00,0x18,0x20,0x20,0x31,0x1E,0x00,/*"3",11*/
};

//字模:"固定电话"
unsigned char code tel[]={
0x00,0x00,0xFC,0x24,0x24,0x24,0xFC,0x24,0x24,0xA4,0x24,0xFE,0x00,0x00,0x00,0x00,
0x7F,0x40,0x4F,0x49,0x48,0x49,0x49,0x5F,0x40,0x7F,0x00,0x00,0x00,0x00,/*"固",0*/
0x00,0x20,0x38,0x90,0x90,0x90,0x8A,0x94,0x90,0x90,0xB0,0x50,0x00,0x00,0x00,0x40,
0x30,0x0F,0x10,0x20,0x3B,0x44,0x44,0x44,0x46,0x44,0x00,0x00,0x00,0x00,/*"定",1*/
0x00,0x00,0xF0,0x90,0x90,0x90,0xFE,0x90,0x90,0x90,0xF0,0x10,0x00,0x00,0x00,0x00,
0x0F,0x08,0x08,0x08,0x7F,0x48,0x48,0x48,0x4F,0x50,0x60,0x00,0x00,0x00,/*"电",2*/
0x00,0x00,0x84,0xCC,0x00,0x40,0x40,0x48,0xFC,0x44,0x44,0x42,0x20,0x00,0x00,0x00,
0x00,0x7F,0x10,0x10,0x7E,0x44,0x43,0x44,0x44,0x7E,0x00,0x00,0x00,0x00,/*"话",3*/
};

//电话号码:"0773-2996883"
unsigned char code tel_num[]={
0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00,/*"0",0*/
0x00,0x38,0x08,0x08,0xE8,0x18,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,/*"7",1*/
0x00,0x38,0x08,0x08,0xE8,0x18,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,/*"7",2*/
0x00,0x30,0x08,0x88,0x88,0x70,0x00,0x00,0x18,0x20,0x20,0x31,0x1E,0x00,/*"3",3*/
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x00,/*"-",4*/
0x00,0xF8,0x08,0x88,0x88,0x08,0x00,0x00,0x19,0x21,0x20,0x31,0x1F,0x00,/*"5",5*/
0xE0,0x10,0x88,0x88,0x88,0x18,0x00,0x0F,0x11,0x20,0x20,0x31,0x1F,0x00,/*"6",6*/
0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00,/*"0",7*/
0xF0,0x08,0x08,0x08,0x18,0xE0,0x00,0x31,0x22,0x22,0x32,0x19,0x07,0x00,/*"9",8*/
0x00,0x80,0x40,0x20,0xF8,0x00,0x00,0x06,0x05,0x04,0x24,0x3F,0x24,0x04,/*"4",9*/
0x00,0xF8,0x08,0x88,0x88,0x08,0x00,0x00,0x19,0x21,0x20,0x31,0x1F,0x00,/*"5",10*/
0x70,0x98,0x88,0x08,0x98,0x70,0x00,0x1E,0x21,0x21,0x21,0x31,0x1E,0x00,/*"8",11*/
};

//字模"0123456789"
unsigned char code num[]={
0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00,/*"0"*/
0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,/*"1"*/
0x00,0x70,0x08,0x08,0x08,0xF0,0x00,0x00,0x30,0x2C,0x22,0x21,0x30,0x00,/*"2"*/
0x00,0x30,0x08,0x88,0x88,0x70,0x00,0x00,0x18,0x20,0x20,0x31,0x1E,0x00,/*"3"*/
0x00,0x80,0x40,0x20,0xF8,0x00,0x00,0x06,0x05,0x04,0x24,0x3F,0x24,0x04,/*"4"*/
0x00,0xF8,0x08,0x88,0x88,0x08,0x00,0x00,0x19,0x21,0x20,0x31,0x1F,0x00,/*"5"*/
0xE0,0x10,0x88,0x88,0x88,0x18,0x00,0x0F,0x11,0x20,0x20,0x31,0x1F,0x00,/*"6"*/
0x00,0x38,0x08,0x08,0xE8,0x18,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,/*"7"*/
0x70,0x98,0x88,0x08,0x98,0x70,0x00,0x1E,0x21,0x21,0x21,0x31,0x1E,0x00,/*"8"*/
0xF0,0x08,0x08,0x08,0x18,0xE0,0x00,0x31,0x22,0x22,0x32,0x19,0x07,0x00,/*"9"*/
};

//字模"--QQ:289994918--"
unsigned char code QQ[]={

0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x00,/*"-",0*/
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x00,/*"-",1*/
0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x0F,0x18,0x24,0x24,0x78,0x4F,0x00,/*"Q",2*/
0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x0F,0x18,0x24,0x24,0x78,0x4F,0x00,/*"Q",3*/
0x00,0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,/*":",4*/
0x00,0x70,0x08,0x08,0x08,0xF0,0x00,0x00,0x30,0x2C,0x22,0x21,0x30,0x00,/*"2",5*/
0x70,0x98,0x88,0x08,0x98,0x70,0x00,0x1E,0x21,0x21,0x21,0x31,0x1E,0x00,/*"8",6*/
0xF0,0x08,0x08,0x08,0x18,0xE0,0x00,0x31,0x22,0x22,0x32,0x19,0x07,0x00,/*"9",7*/
0xF0,0x08,0x08,0x08,0x18,0xE0,0x00,0x31,0x22,0x22,0x32,0x19,0x07,0x00,/*"9",8*/
0xF0,0x08,0x08,0x08,0x18,0xE0,0x00,0x31,0x22,0x22,0x32,0x19,0x07,0x00,/*"9",9*/
0x00,0x80,0x40,0x20,0xF8,0x00,0x00,0x06,0x05,0x04,0x24,0x3F,0x24,0x04,/*"4",10*/
0xF0,0x08,0x08,0x08,0x18,0xE0,0x00,0x31,0x22,0x22,0x32,0x19,0x07,0x00,/*"9",11*/
0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,/*"1",12*/
0x70,0x98,0x88,0x08,0x98,0x70,0x00,0x1E,0x21,0x21,0x21,0x31,0x1E,0x00,/*"8",13*/
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x00,/*"-",14*/
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x00,/*"-",15*/
};

unsigned char code tup[]={
/*--  一幅图像： --*/
/*--  宽度x高度=122x32  --*/
0x00,0x00,0x00,0x70,0xF8,0xF8,0xFC,0xFC,0xFE,0xFE,0xFE,0xFE,0xFC,0xFC,0xF0,0xE0,
0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x80,0x40,0x20,0x10,0x48,0xD4,0xB4,0x62,0xC2,0x82,0x03,0x02,0x02,
0x02,0x84,0xC4,0xE0,0xA0,0xE0,0x60,0x20,0x20,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x80,0xE0,0xB0,0xF8,0xF0,0xF0,0xF8,0xFC,0x60,0x60,0x30,
0x18,0x00,0x00,0x00,0x80,0xC0,0xE0,0xE0,0xF0,0xF0,0xF0,0xD8,0x58,0x58,0x58,0x58,
0x58,0xD8,0xD8,0x98,0xB0,0x30,0x70,0xE0,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x07,
0x07,0x07,0x02,0x7F,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFE,0xFC,0xFC,0xFC,0xFC,
0xFC,0xFC,0xFC,0xFC,0xFC,0xFC,0xFC,0xFC,0xF8,0xF0,0xC0,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFE,0x01,0x00,0x04,
0x0D,0x1B,0x36,0x6D,0xDB,0xF6,0xED,0xFB,0xFE,0xFE,0xFF,0x7F,0x1F,0x07,0x01,0x00,
0x00,0x00,0xF0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF8,0xFC,0xFE,0xFE,
0xFE,0xFF,0xFF,0xFF,0xFF,0xFF,0xFE,0xFC,0xE0,0xC0,0xC0,0xF8,0xFE,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFE,0x3E,0xF8,0x01,0x37,
0x0C,0x00,0x1F,0x00,0x00,0x00,0x00,0x00,0x60,0xFF,0xC7,0x03,0x03,0x03,0x03,0xE1,
0xFF,0x3F,0x0F,0x03,0x03,0x03,0x03,0x03,0x03,0x03,0x03,0x0F,0x3F,0x7F,0xFF,0xEF,
0xBF,0x7F,0xFF,0xC7,0x07,0x1F,0xFE,0xF8,0xB0,0x60,0x80,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x04,0x08,0x10,0x20,0x40,0x40,0x80,0x83,
0xFF,0xFF,0xFF,0xFF,0x83,0x40,0x40,0x20,0x10,0x08,0x04,0x03,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x03,0x03,0x07,0x0F,0x1F,0x3F,0x3F,0x7F,0xFF,
0xFF,0x7F,0x7F,0xFF,0xFF,0xFF,0xFF,0xDF,0x3F,0x3F,0x0F,0x61,0x3F,0x1F,0x2F,0x3F,
0x1F,0x0F,0x00,0x0F,0x07,0x03,0x00,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x18,0x18,0x1E,0x07,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x40,0x60,0x70,0x3C,0x1F,0x07,0x03,0x01,0x01,0x00,0x00,
0x01,0x07,0x07,0x01,0x00,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x7C,0x44,0xEC,0x00,
0x7C,0x44,0x7C,0x00,0x7C,0x40,0x40,0x00,0x7C,0x44,0x38,0x00,0x7C,0x14,0x1C,0x00,
0x7C,0x40,0x40,0x00,0x78,0x24,0x78,0x00,0x7C,0x18,0x18,0x7C,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x20,0x20,0x20,0x20,0x10,0x04,0x07,0x00,0x01,0x00,0x00,0x00,0x01,
0x05,0x03,0x02,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};

/*------------------------------------------*/
void wr_lcd (unsigned char choe1,unsigned char choe2,unsigned char data_comm,unsigned char content)
{
  chk_busy (choe1,choe2);
  if(data_comm)
{
a0=1; //data
rw=0; //write
}
  else
{
a0=0; //command
rw=0; //write
}
  if(choe1==1)
  {
P0=content; //output data or comm
e1=1;
;
e1=0;
  }
  if(choe2==1)
  {
P0=content; //output data or comm
e2=1;
;
e2=0;
  }
}

/**********忙检测***************************************/
void chk_busy (unsigned char choe1,unsigned char choe2)
{
  if(choe1==1)
  {
a0=0;
rw=1;
e1=1;
while(bf==1)
   delay(2);
e1=0;
  }
  if(choe2==1)
  {
a0=0;
rw=1;
e2=1;
while(bf==1)
   delay(2);
e2=0;
  }
}

void delay (unsigned int us) //delay time
{
  while(us--);
}
void delay1 (unsigned int ms)
{
  unsigned int i,j;
  for(i=0;i<ms;i++)
  for(j=0;j<1000;j++)
  ;
}

/************写一串汉字****************************/
/*显示"三木多功能实验板"*/
/*一行八个汉字一起写*/
/*row为0~3的数,其实是把液晶上下两行分成4行即4*8=32
line为0~7的数,液晶一行可以写入像素为长×宽=15*16的八个汉字/
*characters为要写入汉字串的首地址*/
void Write_Chinese_Characters(unsigned char row,unsigned char line,
unsigned char code *characters,unsigned char chinese_num)
{

unsigned char i;
  for(i=0;i<chinese_num ;i++)
{
Write_One_Chinese(row, line+i, characters+30*i);
}

}

/************写一个汉字到任意位置上****************************/
/*---------汉字像素为长×宽=15*16--------*/
//x=0表示写入第一行,x=2表示写入第二行,*characters表示要写的字模数据
//y=(0~7)表示开始写入的列位置,每一行可以写入八个汉字,就是把液晶一行分成8个汉字位置
void Write_One_Chinese(unsigned char x,unsigned char y,unsigned char code *chinese)
{

unsigned char i,j;

for(j=0;j<2;j++)
{
   /////////////////////////////
   wr_lcd (1,0,comm,0xc0);//  列地址指针归零
   ////////////////////////////
   if((y/4)==0)
   {
   wr_lcd (1,0,comm,f_page+j+x);
   wr_lcd (1,0,comm,f_row+x*8);
   wr_lcd (1,0,comm,y*15+j);
   for(i=0;i<15;i++)
      {
      wr_lcd (1,0,dat,chinese[j*15+i]);
}

   }
   else
   {
   wr_lcd (0,1,comm,f_page+j+x);
   wr_lcd (0,1,comm,f_row+x*8);
   wr_lcd (0,1,comm,(y-4)*15+j);
   for(i=0;i<15;i++)
   {
      wr_lcd (0,1,dat,chinese[j*15+i]);}
   }
   //////////////////////////////
// wr_lcd (0,1,comm,0xc0);//列地址指针归零
   //////////////////////////////
}
}

/**********************显示一个字符********************/

void Write_One_Char(unsigned char x,unsigned char y,unsigned char code *one_char)
{
unsigned char i,j;
for(j=0;j<2;j++)
{

   if((y/8)==0)
   {
   wr_lcd (1,0,comm,f_page+j+x);
   wr_lcd (1,0,comm,f_row+x*8);
   wr_lcd (1,0,comm,y*7+5);
   for(i=0;i<7;i++)
      {
      wr_lcd (1,0,dat,one_char[j*7+i]);
}
   /////////////////////////////
   wr_lcd (1,0,comm,0xc0);//  列地址指针归零
   ////////////////////////////
   }
   else
   {
   wr_lcd (0,1,comm,f_page+j+x);
   wr_lcd (0,1,comm,f_row+x*8);
   wr_lcd (0,1,comm,(y-8)*7);
   for(i=0;i<7;i++)
   {
      wr_lcd (0,1,dat,one_char[j*7+i]);}
   }
   //////////////////////////////
   wr_lcd (0,1,comm,0xc0);//列地址指针归零
   //////////////////////////////
}
}

/**************写一串字符**********************/
/****************************************************************************/
/*x=(0~4)--字符行首址;y=(0~15)--字符列首址;char_num=(1~16)--要写入字符的个数*/
/****************************************************************************/
void Write_Chars(unsigned char x,unsigned char y,unsigned char code *chars,unsigned char char_num)
{
unsigned char i;
for(i=0;i<char_num;i++)
{
Write_One_Char( x, y+i, chars+14*i);
}
}

/*----------------画图形-----------------*/
void disptu (unsigned char code *img)
{
  unsigned char i,j;
  for(j=0;j<4;j++)
  {
wr_lcd (1,1,comm,f_page+j);
wr_lcd (1,1,comm,f_row);
wr_lcd (1,1,comm,f_line);
for(i=0;i<122;i++)
{
   if(i<61)
   {wr_lcd (1,0,comm,f_line+i);
   wr_lcd (1,0,dat,img[j*122+i]);}
   else
   {wr_lcd (0,1,comm,f_line+i-61);
   wr_lcd (0,1,dat,img[j*122+i]);}
}
  }
}
/*--------------写点阵------------------*/
void wrlattice (unsigned char data1,unsigned char data2)
{
  unsigned char i,j;
  for(j=0;j<4;j++)
  {
wr_lcd (1,1,comm,f_page+j);
wr_lcd (1,1,comm,f_row);
wr_lcd (1,1,comm,f_line);
for(i=0;i<61;i=i+2)
{
   wr_lcd (1,1,dat,data1);
   wr_lcd (1,1,dat,data2);
}
  }
}

/*------------------初始化-----------------*/
void init_lcd (void)
{
  rst=1;
  wr_lcd (1,1,comm,0xe2);  //软件复位
  wr_lcd (1,1,comm,0xa4);  //动态驱动
// wr_lcd (1,1,comm,0xae);//显示关闭
  wr_lcd (1,1,comm,0xa9); //刷新时钟设置1/32
  wr_lcd (1,1,comm,0xa0); //clockwise
  wr_lcd (1,1,comm,0xee);  //写模式
  wr_lcd (1,1,comm,0xaf);//显示打开

}

/*------------------主程序--------------------*/
void main ()
{
init_lcd ();
while(1)
{
Write_Chinese_Characters(0,0,sanmu,8); //第一行显示"三木多功能实验板"
Write_Chars(2,0,QQ,16);  //第二行显示"--QQ:289994918--"
delay1 (500);
wrlattice (0x00,0x00); //清屏
Write_Chinese_Characters(0,2,moble,4); //第一行中间位置显示"小灵通号"
Write_Chars(2,2,moble_num,12);  //第二行显示"0773-2996883"
delay1 (500);
wrlattice (0x00,0x00); //清屏
Write_Chinese_Characters(0,2,tel,4); //第一行中间位置显示"固定电话"
Write_Chars(2,2,tel_num,12);  //第二行显示"0773-5609458"
delay1 (500);
wrlattice (0x00,0x00); //清屏
disptu (tup);    //显示一幅图片
delay1 (500);
wrlattice (0x00,0x00); //清屏
   }
}

ermeg · 发表于 2008-1-26 21:54:49

太帅了！！！

gumplin · 发表于 2008-4-25 01:12:19

怎么会事,我用这程序我的板子中TS12232D显示不了,不知道什么问题啊.我是这样接的:数据口-----P0;
E1 ----P2_2
E2---- P2_3
res----- P3_4
RW------ P2_4
A0 ----P2_5

望高手指点下!!!!!

pulan · 发表于 2008-4-25 06:14:44

p0口加上拉电阻看看

gumplin · 发表于 2008-4-25 10:23:06

加了4.7K的上拉电阻,没有什么效果

abcdezh · 发表于 2008-4-25 12:10:32

有一快12232，试试
谢谢

gumplin · 发表于 2008-4-27 11:22:35

哪位高手知道上面程序中的字模代码是怎么生成的???望高手指点!!!同时这些代码怎样画出它对应的汉字

pulan · 发表于 2008-4-27 11:33:56

字模软件阿

gumplin · 发表于 2008-4-28 11:35:44

我用的字模软件跟他用的代码不同,所以我就不知道怎么弄了

meisen999 · 发表于 2008-12-10 20:14:11

好久没有老看看了,每哟想到还有那么多兄弟关注.在此表示谢谢!!!

现在将电路图和取字模过程发上来,希望大家能喜欢:

点击此处下载 ourdev_536457.pdf(文件大小:344K) (原文件名:LCD12232.pdf) 

点击此处下载 ourdev_536458.pdf(文件大小:2.30M) (原文件名:№37：LCD12232不带汉字库液晶驱动.pdf) 

点击此处下载 ourdev_536777.rar(文件大小:30K) (原文件名:№37：LCD12232不带汉字库液晶驱动.C.rar) 

本贴被 meisen999 编辑过,最后修改时间：2008-12-10,22:23:25.

shaoshunda · 发表于 2008-11-26 13:53:27

感谢中

lhjnjust · 发表于 2008-11-23 23:53:28

学习了

huike_h · 发表于 2008-11-22 23:01:26

mark一下先.

mwwyi · 发表于 2008-10-17 22:11:32

meisen999大哥，能给个引脚定义吗 

mwwyi · 发表于 2008-10-14 16:45:25

能告诉我这个LCD 各管脚的定义嘛  非常感激

wangxiaoacc · 发表于 2009-4-1 21:59:31

下了你的资料，谢谢

unsv · 发表于 2009-4-4 11:19:52

楼主的程序蛮不错的！！
如果能用指针直接指向数组整个程序会更清晰！！！

ql-dz.com · 发表于 2009-9-19 16:17:26

学习学习.

lordyeye · 发表于 2010-1-29 15:33:27

谢谢楼主的资料

joni · 发表于 2010-1-29 21:29:23

mark

liujinyu · 发表于 2010-4-14 13:29:55

谢谢楼主

sunshine001 · 发表于 2010-8-17 14:09:12

下载了资料，非常感谢楼主！

lyk07351 · 发表于 2010-11-30 10:12:10

Thank you

oct20040821 · 发表于 2011-2-20 09:40:18

谢谢楼主，多多向你学习

ERDTxiduoduo · 发表于 2011-2-20 11:12:11

mark

oaixuw · 发表于 2011-4-9 22:37:42

mark

fxping · 发表于 2011-5-7 17:41:31

怎么程序在电脑上仿真不了呢?

416446891 · 发表于 2011-5-17 03:20:50

真是神奇的论坛啊，我感激你

myqq286477745 · 发表于 2011-5-17 17:06:31

谢谢楼主的分享

airfex · 发表于 2012-1-14 22:14:00

谢谢楼主

senzh01 · 发表于 2012-1-14 22:25:06

感谢了，这种屏用的不多吗？

wtiechen1969 · 发表于 2012-1-14 22:50:24

mark

sszzeettee · 发表于 2012-1-14 23:10:43

谢谢分享

xdco · 发表于 2012-1-15 00:03:03

mark

ppdd · 发表于 2012-5-6 22:46:25

关注中～～～～

sszzeettee · 发表于 2012-5-6 23:54:48

看看

jj123paopao · 发表于 2012-9-20 08:40:22

楼主威武！

lampearl982615 · 发表于 2012-10-25 09:01:06

多谢

LZ

古惑ming · 发表于 2012-10-25 18:08:32

请问有木有串行程序

zhenglu891028 · 发表于 2012-10-26 04:46:15

驅動芯片是什麽的

dory_m · 发表于 2012-10-26 07:40:00

学习，谢谢！！！

lzchuo · 发表于 2012-11-29 16:26:37

能用，感谢

发个LCD12232液晶驱动程序

阿莫论坛20周年了！感谢大家的支持与爱护！！