那位有bascom avr的I2CSLAVE Library文件i2cslave.lib和i2cslave.lbx
编译例程I2CSLAVE_PCF8574.bas时用到，编译错误，提示信息：找不到i2cslave.lib和i2cslave.lbx。哪位大虾有，能提供一下吗？ 补充一下关于这个苦的说明文档：
I2CSLAVE
The I2C-Slave library is intended to create I2C slave chips. This is an add-on library that is not included by default.
All BASCOM I2C routines are master I2C routines. The AVR is a fast chip and allows to implement the I2C slave protocol.
You can control the chips with the BASCOM I2C statements like I2CINIT, I2CSEND, I2CRECEIVE, I2CWBYTE, etc. Please consult the BASCOM Help file for using I2C in master mode.
Before you begin
Copy the i2cslave.lib and i2cslave.lbx files into the BASCOM-AVR\LIB directory.
The i2cslave.lib file contains the ASM source. The i2cslave.lbx file contains the compiled ASM source.
Slave address
Every I2C device must have an address so it can be addressed by the master I2C routines.
When you write to an I2C-slave chip the least significant bit (bit0) is used to specify if we want to read from the chip or that we want to write to the chip.
When you specify the slave address, do not use bit 0 in the address!
For example a PCF8574 has address &H40. To write to the chip use &H40, to read from the chip, use &H41. When emulating a PCF8574 we would specify address &H40.
Use the CONFIG statement to specify the slave address:
Config I2cslave = &B01000000 ' same as &H40
Optional use : CONFIG I2CSLAVE = address, INT= int , TIMER = tmr
Where INT is INT0, INT1 etc. and TIMER is TIMER0, TIMER1 etc.
When using other interrupts or timers, you need to change the library source. The library was written for TIMER0 and INT0.
The I2C slave routines use the TIMER0 and INT0. You can not use these interrupts yourself. It also means that the SCL and SDA pins are fixed.
Note that new AVR chips have a TWI or hardware I2C implementation. It is better to use hardware I2C, then the software I2C. The slave library is intended for AVR chips that do not have hardware I2C.
CONFIG I2CSLAVE will enable the global interrupts.
After you have configured the slave address, you can insert your code.
A do-loop would be best:
Do
?your code here
Loop
This is a simple never-ending loop. You can use a GOTO with a label or a While Wend loop too but ensure that the program will never end.
After your main program you need to insert two labels with a return:
When the master needs to read a byte, the following label is always called
You must put the data you want to send to the master in variable _a1 which is register R16
I2c_master_needs_data:
'when your code is short, you need to put in a waitms statement
'Take in mind that during this routine, a wait state is active and the master will wait
'After the return, the waitstate is ended
Config Portb = Input ' make it an input
_a1 = Pinb ' Get input from portB and assign it
Return 这个是需要购买的，具体内容请参考代理的网站
http://www.avrbascom.com/buySoftware.html 昨天打电话了，不通！
发邮件，没回音！
郁闷！ 邮件已经给您回复了 请您查收。 miamia 发表于 2006-12-6 20:48 static/image/common/back.gif
邮件已经给您回复了 请您查收。
我也要一份zxttgg@gmail.com
页:
[1]