jz2440烧写uboot后，上电启动只停留在企鹅那里卡住
前几天刚买来板子，按照视频烧写了uboot.bin，一切正常。后来在接着烧写了在window下使用dnw.exe发送光盘中的fs_qtopia.yaffs2和uImage，接着就出现了于是再次使用jlink烧写uboot，无论是norflash还是nandflash启动发现也无法改变现状。
Kernel panic - not syncing: No init found.Try passing init= option to kernel.
我不知道这会不会涉及到比较深度的问题要调试，如果有的话，请问下，我是不是可以先跳过这个问题，等学习一段时间入门后再来解决。因为我还没有学习驱动程序，更别说调试。
以下是secureCRT界面显示：
DRAM:64 MB
Flash:2 MB
NAND:256 MiB
*** Warning - bad CRC or NAND, using default environment
In: serial
Out: serial
Err: serial
UPLLVal
MPLLVal
CLKDIVN:5h
+---------------------------------------------+
| S3C2440A USB Downloader ver R0.03 2004 Jan|
+---------------------------------------------+
USB: IN_ENDPOINT:1 OUT_ENDPOINT:3
FORMAT: <ADDR(DATA):4>+<SIZE(n+10):4>+<DATA:n>+<CS:2>
NOTE: Power off/on or press the reset button for 1 sec
in order to get a valid USB device address.
Hit any key to stop autoboot:0
Booting Linux ...
NAND read: device 0 offset 0x60000, size 0x200000
Reading data from 0x25f800 -- 100% complete.
2097152 bytes read: OK
## Booting image at 30007fc0 ...
Image Name: Linux-2.6.22.6
Created: 2011-01-2714:22:53 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1848656 Bytes =1.8 MB
Load Address: 30008000
Entry Point:30008000
Verifying Checksum ... OK
XIP Kernel Image ... OK
Starting kernel ...
Uncompressing Linux...................................................................................................................... done, booting the kernel.
Linux version 2.6.22.6 (book@book-desktop) (gcc version 3.4.5) #1 Thu Jan 27 22:22:51 CST 2011
CPU: ARM920T revision 0 (ARMv4T), cr=c0007177
Machine: SMDK2440
Memory policy: ECC disabled, Data cache writeback
CPU S3C2440A (id 0x32440001)
S3C244X: core 400.000 MHz, memory 100.000 MHz, peripheral 50.000 MHz
S3C24XX Clocks, (c) 2004 Simtec Electronics
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists.Total pages: 16256
Kernel command line: noinitrd root=/dev/mtdblock3 init=/linuxrc console=ttySAC0
irq: clearing pending ext status 00000200
irq: clearing subpending status 00000002
PID hash table entries: 256 (order: 8, 1024 bytes)
timer tcon=00500000, tcnt a2c1, tcfg 00000200,00000000, usec 00001eb8
Console: colour dummy device 80x30
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 60976KB available (3264K code, 458K data, 140K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
S3C2410 Power Management, (c) 2004 Simtec Electronics
S3C2440: Initialising architecture
S3C2440: IRQ Support
S3C2440: Clock Support, DVS off
S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics
DMA channel 0 at c4800000, irq 33
DMA channel 1 at c4800040, irq 34
DMA channel 2 at c4800080, irq 35
DMA channel 3 at c48000c0, irq 36
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NetWinder Floating Point Emulator V0.97 (double precision)
Registering GDB sysrq handler
JFFS2 version 2.2. (NAND) 漏 2001-2006 Red Hat, Inc.
yaffs Jan 27 2011 22:22:18 Installing.
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Console: switching to colour frame buffer device 30x40
fb0: s3c2410fb frame buffer device
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
s3c2440-uart.0: s3c2410_serial0 at MMIO map 0x50000000 mem 0xf0400000 (irq = 70) is a S3C2440
s3c2440-uart.1: s3c2410_serial1 at MMIO map 0x50004000 mem 0xf0404000 (irq = 73) is a S3C2440
s3c2440-uart.2: s3c2410_serial2 at MMIO map 0x50008000 mem 0xf0408000 (irq = 76) is a S3C2440
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: module loaded
line 400 <DM9KS> I/O: c486a000, VID: 90000a46
line 408 <DM9KS> I/O: c486a000, VID: 90000a46
<DM9KS> error version, chip_revision = 0x1a, chip_info = 0x3
id_val=0
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2440-nand s3c2440-nand: Tacls=3, 30ns Twrph0=7 70ns, Twrph1=3 30ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 25 at 0x00320000
Bad eraseblock 273 at 0x02220000
Bad eraseblock 461 at 0x039a0000
Bad eraseblock 1015 at 0x07ee0000
Creating 4 MTD partitions on "NAND 256MiB 3,3V 8-bit":
0x00000000-0x00040000 : "bootloader"
0x00040000-0x00060000 : "params"
0x00060000-0x00260000 : "kernel"
0x00260000-0x10000000 : "root"
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
s3c2410 TouchScreen successfully loaded
input: s3c2410 TouchScreen as /class/input/input0
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2440-i2c s3c2440-i2c: slave address 0x10
s3c2440-i2c s3c2440-i2c: bus frequency set to 390 KHz
s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
mapped channel 0 to 0
s3c2440-sdi s3c2440-sdi: powered down.
s3c2440-sdi s3c2440-sdi: initialisation done.
s3c2440-sdi s3c2440-sdi: running at 0kHz (requested: 0kHz).
s3c2440-sdi s3c2440-sdi: running at 196kHz (requested: 195kHz).
s3c2440-sdi s3c2440-sdi: running at 196kHz (requested: 195kHz).
s3c2440-sdi s3c2440-sdi: running at 196kHz (requested: 195kHz).
usbcore: registered new interface driver hiddev
s3c2440-sdi s3c2440-sdi: CMD #2 op:UNKNOWN(8) arg:0x000001aa flags:0x0875 retries:0 Status:nothing to complete
s3c2440-sdi s3c2440-sdi: CMD #3 op:APP_CMD(55) arg:0x00000000 flags:0x0875 retries:0 Status:nothing to complete
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.14 (Thu May 31 09:03:25 2007 UTC).
ASoC version 0.13.1
s3c2440-sdi s3c2440-sdi: CMD #4 op:APP_CMD(55) arg:0x00000000 flags:0x0875 retries:0 Status:nothing to complete
s3c2440-sdi s3c2440-sdi: CMD #5 op:APP_CMD(55) arg:0x00000000 flags:0x0875 retries:0 Status:nothing to complete
s3c2410iis_probe...
s3c2440-sdi s3c2440-sdi: CMD #6 op:APP_CMD(55) arg:0x00000000 flags:0x0875 retries:0 Status:nothing to complete
s3c2440-sdi s3c2440-sdi: CMD #7 op:ALL_SEND_OCR(1) arg:0x00000000 flags:0x0861 retries:0 Status:nothing to complete
s3c2440-sdi s3c2440-sdi: powered down.
UDA1341 audio driver initialized
ALSA device list:
No soundcards found.
TCP cubic registered
NET: Registered protocol family 1
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
UDF-fs: No VRS found
yaffs: dev is 32505859 name is "mtdblock3"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.3, "mtdblock3"
yaffs: auto selecting yaffs2
block 7 is bad
block 255 is bad
block 443 is bad
block 997 is bad
VFS: Mounted root (yaffs filesystem).
Freeing init memory: 140K
Warning: unable to open an initial console.
Failed to execute /linuxrc.Attempting defaults...
Kernel panic - not syncing: No init found.Try passing init= option to kernel.
文件系统不正常 fs_qtopia.yaffs2 烧的不对，或者有问题 block 7 is bad
block 255 is bad
block 443 is bad
block 997 is bad
tongdayusu 发表于 2013-4-20 16:22 static/image/common/back.gif
block 7 is bad
block 255 is bad
block 443 is bad
我烧写的文件是从光盘拷贝过来的。 tongdayusu 发表于 2013-4-20 16:21 static/image/common/back.gif
文件系统不正常
我曾试着重新烧写uboot，但是也是这个样子，难道说板子的文件系统被我破坏了 不是nandFlash坏掉就好。 ARMjerry 发表于 2013-4-22 21:02 static/image/common/back.gif
另外你的液晶屏是4.3寸的，应该烧写4.3寸的uImage，看你的图片烧写的是3.5寸的 ...
谢谢，解决了！ yidehui 发表于 2013-4-22 21:30 static/image/common/back.gif
谢谢，解决了！
请问怎么解决的啊 ，我和你一样的问题
请问是怎么解决的啊？ 4.3寸的uImage 你烧错内核文件了 烧了3.5寸屏的 应该烧4.3寸的内核才是
页:
[1]