a178119559 发表于 2011-7-23 22:23:31

OURDSO_Winter_2010刷机后白屏，但可以联机问题请教

程序烧写结果
http://cache.amobbs.com/bbs_upload782111/files_43/ourdev_660460OATJJ2.jpg
(原文件名:ourdev_658729GZ5SJD.jpg)

开机白屏~
开机能听见继电器吸合~嗒~
请问这样说明硬件正常吗~

armok 发表于 2011-7-23 22:30:04

kunnsd 发表于 2011-7-23 22:43:11

回复【楼主位】a178119559
-----------------------------------------------------------------------

从截图看这个程序没有下载成功，下载时要选择将.sof配置文件同时下载进EPCS存储器，否则无法启动，请参考以下链接，该链接是专为Winter 2010刷程序写的教程：
http://www.ourdev.cn/bbs/bbs_content.jsp?bbs_sn=4623427&bbs_page_no=1&bbs_id=3051

a178119559 发表于 2011-7-23 23:38:12

代码为~2011年6月14日更新工程包，去掉了多余的影响编译的函数。

认真按照教材做了   下载提示如下：

#!/bin/sh
#
# This file was automatically generated by the Nios II IDE Flash Programmer.
#
# It will be overwritten when the flash programmer options change.
#

cd E:/Winter_2010/software/Winter_2010_soft/Debug

# Creating .flash file for the FPGA configuration
"$SOPC_KIT_NIOS2/bin/sof2flash" --epcs --input="E:/Winter_2010/Winter_2010.sof"
--output="Winter_2010.flash"
Info: *******************************************************************
Info: Running Quartus II Convert_programming_file
Info: Command: quartus_cpf --no_banner --convert --device=EPCS128 --option=Winte
r_2010.opt E:/Winter_2010/Winter_2010.sof Winter_2010.pof
Info: Quartus II Convert_programming_file was successful. 0 errors, 0 warnings
    Info: Peak virtual memory: 68 megabytes
    Info: Processing ended: Sun Jul 24 23:33:12 2011
    Info: Elapsed time: 00:00:03
    Info: Total CPU time (on all processors): 00:00:02
Info: *******************************************************************
Info: Running Quartus II Convert_programming_file
Info: Command: quartus_cpf --no_banner --convert Winter_2010.pof Winter_2010.rpd
Info: Quartus II Convert_programming_file was successful. 0 errors, 0 warnings
    Info: Peak virtual memory: 66 megabytes
    Info: Processing ended: Sun Jul 24 23:33:15 2011
    Info: Elapsed time: 00:00:03
    Info: Total CPU time (on all processors): 00:00:02

# Programming flash with the FPGA configuration
"$SOPC_KIT_NIOS2/bin/nios2-flash-programmer" --epcs --base=0x01001800 --instance
=0 "Winter_2010.flash"
Using cable "USB-Blaster ", device 1, instance 0x00
Resetting and pausing target processor: OK
No EPCS layout data - looking for section
Unable to use EPCS device
Leaving target processor paused

# Creating .flash file for the project
"$SOPC_KIT_NIOS2/bin/elf2flash" --epcs --after="Winter_2010.flash" --input="Wint
er_2010_soft.elf" --output="epcs_controller.flash"

# Programming flash with the project
"$SOPC_KIT_NIOS2/bin/nios2-flash-programmer" --epcs --base=0x01001800 --instance
=0 "epcs_controller.flash"
Using cable "USB-Blaster ", device 1, instance 0x00
Resetting and pausing target processor: OK
No EPCS layout data - looking for section
Unable to use EPCS device
Leaving target processor paused

a178119559 发表于 2011-7-23 23:40:55

配置文件烧写结果：
Info: Started Programmer operation at Sun Jul 24 23:38:53 2011
Info: Configuring device index 1
Info: Device 1 contains JTAG ID code 0x020F10DD
Info: Configuration succeeded -- 1 device(s) configured
Info: Successfully performed operation(s)
Info: Ended Programmer operation at Sun Jul 24 23:38:57 2011

a178119559 发表于 2011-7-24 00:19:01

好像下载成功但是还是白屏
#!/bin/sh
#
# This file was automatically generated by the Nios II IDE Flash Programmer.
#
# It will be overwritten when the flash programmer options change.
#

cd E:/Winter_2010/software/Winter_2010_soft/Debug

# Creating .flash file for the FPGA configuration
"$SOPC_KIT_NIOS2/bin/sof2flash" --epcs --input="E:/Winter_2010/Winter_2010.sof"
--output="Winter_2010.flash"
Info: *******************************************************************
Info: Running Quartus II Convert_programming_file
Info: Command: quartus_cpf --no_banner --convert --device=EPCS128 --option=Winte
r_2010.opt E:/Winter_2010/Winter_2010.sof Winter_2010.pof
Info: Quartus II Convert_programming_file was successful. 0 errors, 0 warnings
    Info: Peak virtual memory: 68 megabytes
    Info: Processing ended: Mon Jul 25 00:12:29 2011
    Info: Elapsed time: 00:00:02
    Info: Total CPU time (on all processors): 00:00:02
Info: *******************************************************************
Info: Running Quartus II Convert_programming_file
Info: Command: quartus_cpf --no_banner --convert Winter_2010.pof Winter_2010.rpd
Info: Quartus II Convert_programming_file was successful. 0 errors, 0 warnings
    Info: Peak virtual memory: 66 megabytes
    Info: Processing ended: Mon Jul 25 00:12:32 2011
    Info: Elapsed time: 00:00:02
    Info: Total CPU time (on all processors): 00:00:02

# Programming flash with the FPGA configuration
"$SOPC_KIT_NIOS2/bin/nios2-flash-programmer" --epcs --base=0x01001800 --cable='U
SB-Blaster ' --device=1 --instance=0 "Winter_2010.flash"
Using cable "USB-Blaster ", device 1, instance 0x00
Resetting and pausing target processor: OK

            : Checksumming existing contents         

00000000      : Verifying existing contents            

00010000      : Verifying existing contents            

00020000      : Verifying existing contents            

00000000      : Reading existing contents               

00010000      : Reading existing contents               

00020000      : Reading existing contents               

Checksummed/read 33kB in 3.5s                                       

00000000 ( 0%): Erasing                                 

00010000 (33%): Erasing                                 

00020000 (66%): Erasing                                 

Erased 192kB in 2.0s (96.0kB/s)                        

00000000 ( 0%): Programming                           

00010000 (33%): Programming                           

00020000 (66%): Programming                           

Programmed 160KB +32KB in 9.9s (19.3KB/s)                  
Did not attempt to verify device contents
Leaving target processor paused

# Creating .flash file for the project
"$SOPC_KIT_NIOS2/bin/elf2flash" --epcs --after="Winter_2010.flash" --input="Wint
er_2010_soft.elf" --output="epcs_controller.flash"

# Programming flash with the project
"$SOPC_KIT_NIOS2/bin/nios2-flash-programmer" --epcs --base=0x01001800 --cable='U
SB-Blaster ' --device=1 --instance=0 "epcs_controller.flash"
Using cable "USB-Blaster ", device 1, instance 0x00
Resetting and pausing target processor: OK

            : Checksumming existing contents         

00020000      : Verifying existing contents            

00030000      : Verifying existing contents            

00040000      : Verifying existing contents            

00050000      : Verifying existing contents            

00060000      : Verifying existing contents            

00020000      : Reading existing contents               

00030000      : Reading existing contents               

00040000      : Reading existing contents               

00050000      : Reading existing contents               

00060000      : Reading existing contents               

Checksummed/read 90kB in 9.5s                                       

00020000 ( 0%): Erasing                                 

00030000 (20%): Erasing                                 

00040000 (40%): Erasing                                 

00050000 (60%): Erasing                                 

00060000 (80%): Erasing                                 

Erased 320kB in 3.4s (94.1kB/s)                        

00020000 ( 0%): Programming                           

00030000 (20%): Programming                           

00040000 (40%): Programming                           

00050000 (60%): Programming                           

00060000 (80%): Programming                           

Programmed 231KB +89KB in 13.6s (23.5KB/s)               
Did not attempt to verify device contents
Leaving target processor paused

ppptawong 发表于 2011-7-24 03:39:38

URDSO_Winter_2010刷机后白屏,
http://www.ourdev.cn/bbs/bbs_content.jsp?bbs_sn=4801203&bbs_page_no=1&bbs_id=305
請問有沒有成功刷机??

ccmj4708 发表于 2011-7-30 08:26:10

回复【楼主位】a178119559
-----------------------------------------------------------------------

如果是9.1版本的，请在软件上修改，把“int alt_main()”这条语句改为“int main()”，然后重新编译一下。
页: [1]
查看完整版本: OURDSO_Winter_2010刷机后白屏，但可以联机问题请教